注塑词汇汇总
本帖最后由 氟塑爱好者 于 2008-12-18 20:25 编辑Injection machine 啤机Shot size（weight） 实际射胶量 injection volume 理论射胶量min mold height 最小容模厚度 Max mold height 最大容模厚度Tie bar clearance 拉杆间距 Die plate size 模板尺寸Ejector stroke 顶出行程 barrel 炮筒，机筒clamp force 锁模力 non-return valve 止回阀 shear 剪切 opening 开模行程Injection pressure 射胶压力 back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期 down time 停机时间 hopper 料筒Mold release 脱模剂 lubrication 润滑work horse 主力，主要设备Reserve pressure / packing pressure保压 mold trial 试模 shot （一）啤Decompress减压 oven 烤炉，烘灶 shrinkage rate 收缩率Residence time 滞留时间 injection speed 注射速度booster time 增压时间Compression ratio 压缩比 mold close time 合模时间Resin胶料Plastification 塑化，增塑 viscosity 粘性，粘度 contamination 污染，杂物Thermoplastic 热塑性塑料 thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充 purge净化Flame retardant 阻燃 degradation降解，软化 regrind 再粉碎Water absorption 吸水 reinforce 增强，加固 specific gravity 比重Elongation 延伸率 density 密度 melting point 熔点 Polystyrene 聚苯乙烯（PS） Styrene 苯乙烯 Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP） Polyethylene 聚乙烯 glass fiber 玻纤Condensation 凝固，浓缩 crystalline resin 结晶形塑料 compre sion molding 压缩成型flash mold 溢流式模具 plsitive mold 挤压式模具 split mold 分割式模具cavity 型控 母模 core 模心 公模 taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值 self tapping screw 自攻螺丝striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型 （射出成型用模具）two plate 两极式（模具） well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器spindle 阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板 insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统 stress crack 应力电裂 orientation 定向 sprue gate 射料浇口，直浇口 nozzle 射嘴 sprue lock pin 料头钩销(拉料杆) slag well 冷料井 side gate 侧浇口edge gate 侧缘浇口 tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口 dish gate 因盘形浇口diaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口 pin gate 针点浇口 Runner less 无浇道 (sprue less) 无射料管方式 long nozzle 延长喷嘴方式 sprue 浇口;溶渣入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter流道: runner热流道： hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode
塑料成形模具 mould for plastics 热塑性塑料模 mould for thermoplastics 热固性塑料模 mould for thermosets 压缩模 compression mould 压注模、传递模 transfer mould 注射模 injection mould 热塑性塑料注射模 injection mould for thermoplastics 热固性塑料注射模 injection mould for thermoses 定模 stationary mould fixed half 动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate 下模座板 lower clamping plate 凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate 凸模固定板 punch-retainer plate 模套 chase. bolster. frame 支承板 backing plate. supprr plate 垫块 spacer parallel 支架 ejector housing. mould base leg abrasive grinding 强力injection mould 注塑模 injection 注射 in-line-of-draw 直接脱模 insert 嵌件 inserted die 嵌入式凹模 inspection检查,监督 installation安装 Surface Appearance 外观 Glossiness/gloss finish 光洁度 Matt finish/matt surface 毛面 Glass fiber rich surface/glass emergence on the surface 玻纤外露 Blooming/surface blooming 表面析出 White patches on surface 表面白斑 Silver marks/silver streak 银纹 Splay mark 水纹 Flow mark 流纹 Weld line 溶结纹 Brittle/brittleness 脆 Bubbles/trapped gas 气泡 Void 孔 Burn marks 烧伤 FR failed 阻燃不合格 Flame rating V-2 阻燃V-2 Poor dispersion 分散不好 FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块 Pellet porous 粒子不密/蜜蜂窝 Low impact/tensile etc 物理性能低 High flow/filler content etc 流动性/填充…过高 Longs/fines/doubles 长粒/碎屑/连粒 Poor cut 粒形不好 Bristle/voids 表面有小气泡/孔 Glass bundles 玻纤结团 Product was rejected due to 产品不能接受因为… High moisture level 高水分 Warpage/warped 翘曲 Shrinkage/shrink 收缩 Sink marks 缩影 Short shot/short molding 打不满 Distortion 变形 Over dimension 尺寸过大 Under dimension 尺寸过小 Flashing 飞边 Discoloration 变色 Off color 颜色差异 Flow rate 流动率 Viscous 粘 High flow 高流动 Low flow 低流动 Sticky 粘 Mold release 脱模 Antioxidant 抗氧剂 Flame retardant agent 阻燃剂 Heat stabilizer 热稳定剂 Chopped glass fiber 短切玻纤 Roving glass fiber 粗纱/长玻纤 Glass beads 玻璃微珠 Milled fiber 碾磨纤 Molybdenum disulfide/moly/MoS2 二硫化钼 Colorant 着色剂 Pigment 颜料 Dye 染料 Accepted product specification 接受产品规格 Approved our product 认可我们的产品 Re-set spec 重新定标准 Add in extra … 添加多一点… Reduced … content 减少…含量 Dropped/reduced … by x％ 减少…含量…％ Confirmed color standard 确认颜色标准 Approved color standard 认可颜色标准 Re-confirmed color standard 重新确认颜色标准 Qualified our product 认可我们的产品 Undergoing heat aging test 在做热老化实验 Product is under testing 产品在测试当中 Received first order 接了第一个定单 Expected to finish by … 预计在…完成 Expected order is xMT 预计定单量…吨 Estimated annual/monthly consumption 预计年/月用量 SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration 动态试验dynamic test 环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss 击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength 冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力internal stress 疲劳fatigue 蠕变creep 试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability 抽样sampling 样品数量sample size AQL Acceptable Quality level 批量lot size 抽样计划sampling plan OC曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance XX电子有限公司XX Electronics CO., Ltd 总经理办公室General manager’s office 企管部Enterprise management department (EM) 行政部Administration department (AD) 销售部Sales department (SD) 财务部Financial department (FD) 技术部Technology department (TD) 物控部Production material control department (PMC) 生产部Production department(PD) 模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop 总经理General manager (GM) 副总经理Vice-general manager 经理manager 董事长president 副董事长Vice-president XX部门经理Manager of XX department 主任、主管supervisor 拉长Line leader 组长Foreman, forelady 秘书secretary 文员clerk 操作员operator 助理assistant 长见识了 比较实用
页:
[1]